Chapter 5. EJBs on JBoss - JBoss Application Server 4.0.4 release5 Guide 英文版指南文档

When the VerifyDeployments attribute of the EJBDeployer is true, the deployer performs a verification of EJBs in the deployment. The verification checks that an EJB meets EJB specification compliance. This entails validating that the EJB deployment unit contains the required home and remote, local home and local interfaces. It will also check that the objects appearing in these interfaces are of the proper types and that the required methods are present in the implementation class. This is a useful behavior that is enabled by default since there are a number of steps that an EJB developer and deployer must perform correctly to construct a proper EJB JAR, and it is easy to make a mistake. The verification stage attempts to catch any errors and fail the deployment with an error that indicates what needs to be corrected.

Probably the most problematic aspect of writing EJBs is the fact that there is a disconnection between the bean implementation and its remote and home interfaces, as well as its deployment descriptor configuration. It is easy to have these separate elements get out of synch. One tool that helps eliminate this problem is XDoclet. It allows you to use custom JavaDoc-like tags in the EJB bean implementation class to generate the related bean interfaces, deployment descriptors and related objects. See the XDoclet home page, http://sourceforge.net/projects/xdoclet for additional details.

The most important role performed by the EJBDeployer is the creation of an EJB container and the deployment of the EJB into the container. The deployment phase consists of iterating over EJBs in an EJB JAR, and extracting the bean classes and their metadata as described by the ejb-jar.xml and jboss.xml deployment descriptors. For each EJB in the EJB JAR, the following steps are performed:

If all EJBs are successfully deployed, the application is started which in turn starts all containers and makes the EJBs available to clients. If any EJB fails to deploy, a deployment exception is thrown and the deployment module is failed.

JBoss externalizes most if not all of the setup of the EJB containers using an XML file that conforms to the jboss_4_0.dtd. The section DTD that relates to container configuration information is shown in Figure 5.4, “The jboss_4_0 DTD elements related to container configuration.”.

Figure 5.4. The jboss_4_0 DTD elements related to container configuration.

The container-configuration element and its subelements specify container configuration settings for a type of container as given by the container-name element. Each configuration specifies information such as the default invoker type, the container interceptor makeup, instance caches/pools and their sizes, persistence manager, security, and so on. Because this is a large amount of information that requires a detailed understanding of the JBoss container architecture, JBoss ships with a standard configuration for the four types of EJBs. This configuration file is called standardjboss.xml and it is located in the conf directory of any configuration file set that uses EJBs. The following is a sample of container-configuration from standardjboss.xml.

<container-configuration>
    <container-name>Standard CMP 2.x EntityBean</container-name>
    <call-logging>false</call-logging>
    <invoker-proxy-binding-name>entity-rmi-invoker</invoker-proxy-binding-name>
    <sync-on-commit-only>false</sync-on-commit-only>
    <insert-after-ejb-post-create>false</insert-after-ejb-post-create>
    <call-ejb-store-on-clean>true</call-ejb-store-on-clean>
    <container-interceptors>
        <interceptor>org.jboss.ejb.plugins.ProxyFactoryFinderInterceptor</interceptor>
        <interceptor>org.jboss.ejb.plugins.LogInterceptor</interceptor>
        <interceptor>org.jboss.ejb.plugins.SecurityInterceptor</interceptor>
        <interceptor>org.jboss.ejb.plugins.TxInterceptorCMT</interceptor>
        <interceptor>org.jboss.ejb.plugins.CallValidationInterceptor</interceptor>
        <interceptor metricsEnabled="true">
            org.jboss.ejb.plugins.MetricsInterceptor
        </interceptor>
        <interceptor>org.jboss.ejb.plugins.EntityCreationInterceptor</interceptor>
        <interceptor>org.jboss.ejb.plugins.EntityLockInterceptor</interceptor>
        <interceptor>org.jboss.ejb.plugins.EntityInstanceInterceptor</interceptor>
        <interceptor>org.jboss.ejb.plugins.EntityReentranceInterceptor</interceptor>
        <interceptor>
             org.jboss.resource.connectionmanager.CachedConnectionInterceptor
        </interceptor>
        <interceptor>org.jboss.ejb.plugins.EntitySynchronizationInterceptor</interceptor>
        <interceptor>org.jboss.ejb.plugins.cmp.jdbc.JDBCRelationInterceptor</interceptor>
    </container-interceptors>
    <instance-pool>org.jboss.ejb.plugins.EntityInstancePool</instance-pool>
    <instance-cache>org.jboss.ejb.plugins.InvalidableEntityInstanceCache</instance-cache>
    <persistence-manager>org.jboss.ejb.plugins.cmp.jdbc.JDBCStoreManager</persistence-manager>
    <locking-policy>org.jboss.ejb.plugins.lock.QueuedPessimisticEJBLock</locking-policy>
    <container-cache-conf>
        <cache-policy>org.jboss.ejb.plugins.LRUEnterpriseContextCachePolicy</cache-policy>
        <cache-policy-conf>
            <min-capacity>50</min-capacity>
            <max-capacity>1000000</max-capacity>
            <overager-period>300</overager-period>
            <max-bean-age>600</max-bean-age>
            <resizer-period>400</resizer-period>
            <max-cache-miss-period>60</max-cache-miss-period>
            <min-cache-miss-period>1</min-cache-miss-period>
            <cache-load-factor>0.75</cache-load-factor>
        </cache-policy-conf>
    </container-cache-conf>
    <container-pool-conf>
        <MaximumSize>100</MaximumSize>
    </container-pool-conf>
    <commit-option>B</commit-option>
</container-configuration>

These two examples demonstrate how extensive the container configuration options are. The container configuration information can be specified at two levels. The first is in the standardjboss.xml file contained in the configuration file set directory. The second is at the EJB JAR level. By placing a jboss.xml file in the EJB JAR META-INF directory, you can specify either overrides for container configurations in the standardjboss.xml file, or entirely new named container configurations. This provides great flexibility in the configuration of containers. As you have seen, all container configuration attributes have been externalized and as such are easily modifiable. Knowledgeable developers can even implement specialized container components, such as instance pools or caches, and easily integrate them with the standard container configurations to optimize behavior for a particular application or environment.

How an EJB deployment chooses its container configuration is based on the explicit or implict jboss/enterprise-beans/<type>/configuration-name element. The configuration-name element is a link to a container-configurations/container-configuration element in Figure 5.4, “The jboss_4_0 DTD elements related to container configuration.”. It specifies which container configuration to use for the referring EJB. The link is from a configuration-name element to a container-name element.

You are able to specify container configurations per class of EJB by including a container-configuration element in the EJB definition. Typically one does not define completely new container configurations, although this is supported. The typical usage of a jboss.xml level container-configuration is to override one or more aspects of a container-configuration coming from the standardjboss.xml descriptor. This is done by specifying container-configuration that references the name of an existing standardjboss.xml container-configuration/container-name as the value for the container-configuration/extends attribute. The following example shows an example of defining a new Secured Stateless SessionBean configuration that is an extension of the Standard Stateless SessionBean configuration.

<?xml version="1.0"?>
<jboss>
    <enterprise-beans>
        <session>
            <ejb-name>EchoBean</ejb-name>
            <configuration-name>Secured Stateless SessionBean</configuration-name>
            <!-- ... -->
        </session>
    </enterprise-beans>
    <container-configurations>
        <container-configuration extends="Standard Stateless SessionBean">
            <container-name>Secured Stateless SessionBean</container-name>
            <!-- Override the container security domain -->
            <security-domain>java:/jaas/my-security-domain</security-domain>
        </container-configuration>
    </container-configurations>
</jboss>

If an EJB does not provide a container configuration specification in the deployment unit EJB JAR, the container factory chooses a container configuration from the standardjboss.xml descriptor based on the type of the EJB. So, in reality there is an implicit configuration-name element for every type of EJB, and the mappings from the EJB type to default container configuration name are as follows:

It is not necessary to indicate which container configuration an EJB is using if you want to use the default based on the bean type. It probably provides for a more self-contained descriptor to include the configuration-name element, but this is purely a matter of style.

Now that you know how to specify which container configuration an EJB is using and can define a deployment unit level override, we now will look at the container-configuration child elements in the following sections. A number of the elements specify interface class implementations whose configuration is affected by other elements, so before starting in on the configuration elements you need to understand the org.jboss.metadata.XmlLoadable interface.

The XmlLoadable interface is a simple interface that consists of a single method. The interface definition is:

import org.w3c.dom.Element;
public interface XmlLoadable
{
    public void importXml(Element element) throws Exception;
}

Classes implement this interface to allow their configuration to be specified via an XML document fragment. The root element of the document fragment is what would be passed to the importXml method. You will see a few examples of this as the container configuration elements are described in the following sections.

5.3.1.3.9. The container-pool-conf element

The container-pool-conf is passed to the InstancePool implementation class given by the instance-pool element if it implements the XmlLoadable interface. All current JBoss InstancePool implementations derive from the org.jboss.ejb.plugins.AbstractInstancePool class which provides support for elements shown in Figure 5.5, “The container-pool-conf element DTD”.

Figure 5.5. The container-pool-conf element DTD

• MinimumSize: The MinimumSize element gives the minimum number of instances to keep in the pool, although JBoss does not currently seed an InstancePool to the MinimumSize value.

• MaximumSize: The MaximumSize specifies the maximum number of pool instances that are allowed. The default use of MaximumSize may not be what you expect. The pool MaximumSize is the maximum number of EJB instances that are kept available, but additional instances can be created if the number of concurrent requests exceeds the MaximumSize value.

• strictMaximumSize: If you want to limit the maximum concurrency of an EJB to the pool MaximumSize, you need to set the strictMaximumSize element to true. When strictMaximumSize is true, only MaximumSize EJB instances may be active. When there are MaximumSize active instances, any subsequent requests will be blocked until an instance is freed back to the pool. The default value for strictMaximumSize is false.

• strictTimeout: How long a request blocks waiting for an instance pool object is controlled by the strictTimeout element. The strictTimeout defines the time in milliseconds to wait for an instance to be returned to the pool when there are MaximumSize active instances. A value less than or equal to 0 will mean not to wait at all. When a request times out waiting for an instance a java.rmi.ServerException is generated and the call aborted. This is parsed as a Long so the maximum possible wait time is 9,223,372,036,854,775,807 or about 292,471,208 years, and this is the default value.

5.3.1.3.11. The container-cache-conf element

The container-cache-conf element is passed to the InstanceCache implementation if it supports the XmlLoadable interface. All current JBoss InstanceCache implementations derive from the org.jboss.ejb.plugins.AbstractInstanceCache class which provides support for the XmlLoadable interface and uses the cache-policy child element as the fully qualified class name of an org.jboss.util.CachePolicy implementation that is used as the instance cache store. The cache-policy-conf child element is passed to the CachePolicy implementation if it supports the XmlLoadable interface. If it does not, the cache-policy-conf will silently be ignored.

There are two JBoss implementations of CachePolicy used by the standardjboss.xml configuration that support the current array of cache-policy-conf child elements. The classes are org.jboss.ejb.plugins.LRUEnterpriseContextCachePolicy and org.jboss.ejb.plugins.LRUStatefulContextCachePolicy. The LRUEnterpriseContextCachePolicy is used by entity bean containers while the LRUStatefulContextCachePolicy is used by stateful session bean containers. Both cache policies support the following cache-policy-conf child elements, shown in Figure 5.6, “The container-cache-conf element DTD”.

Figure 5.6. The container-cache-conf element DTD

• min-capacity: specifies the minimum capacity of this cache

• max-capacity: specifies the maximum capacity of the cache, which cannot be less than min-capacity.

• overager-period: specifies the period in seconds between runs of the overager task. The purpose of the overager task is to see if the cache contains beans with an age greater than the max-bean-age element value. Any beans meeting this criterion will be passivated.

• max-bean-age: specifies the maximum period of inactivity in seconds a bean can have before it will be passivated by the overager process.

• resizer-period: specifies the period in seconds between runs of the resizer task. The purpose of the resizer task is to contract or expand the cache capacity based on the remaining three element values in the following way. When the resizer task executes it checks the current period between cache misses, and if the period is less than the min-cache-miss-period value the cache is expanded up to the max-capacity value using the cache-load-factor. If instead the period between cache misses is greater than the max-cache-miss-period value the cache is contracted using the cache-load-factor.

• max-cache-miss-period: specifies the time period in seconds in which a cache miss should signal that the cache capacity be contracted. It is equivalent to the minimum miss rate that will be tolerated before the cache is contracted.

• min-cache-miss-period: specifies the time period in seconds in which a cache miss should signal that the cache capacity be expanded. It is equivalent to the maximum miss rate that will be tolerated before the cache is expanded.

• cache-load-factor: specifies the factor by which the cache capacity is contracted and expanded. The factor should be less than 1. When the cache is contracted the capacity is reduced so that the current ratio of beans to cache capacity is equal to the cache-load-factor value. When the cache is expanded the new capacity is determined as current-capacity * 1/cache-load-factor. The actual expansion factor may be as high as 2 based on an internal algorithm based on the number of cache misses. The higher the cache miss rate the closer the true expansion factor will be to 2.

The LRUStatefulContextCachePolicy also supports the remaining child elements:

• remover-period: specifies the period in seconds between runs of the remover task. The remover task removes passivated beans that have not been accessed in more than max-bean-life seconds. This task prevents stateful session beans that were not removed by users from filling up the passivation store.

• max-bean-life: specifies the maximum period of inactivity in seconds that a bean can exist before being removed from the passivation store.

An alternative cache policy implementation is the org.jboss.ejb.plugins.NoPassivationCachePolicy class, which simply never passivates instances. It uses an in-memory HashMap implementation that never discards instances unless they are explicitly removed. This class does not support any of the cache-policy-conf configuration elements.

5.3.1.3.17. cluster-config

The cluster-config element allows to specify cluster specific settings for all EJBs that use the container configuration. Specficiation of the cluster configuration may be done at the container configuration level or at the individual EJB deployment level.

Figure 5.7. The cluster-config and related elements

• partition-name: The partition-name element indicates where to find the org.jboss.ha.framework.interfaces.HAPartition interface to be used by the container to exchange clustering information. This is not the full JNDI name under which HAPartition is bound. Rather, it should correspond to the PartitionName attribute of the ClusterPartitionMBean service that is managing the desired cluster. The actual JNDI name of the HAPartition binding will be formed by appending /HASessionState/ to the partition-name value. The default value is DefaultPartition.

• home-load-balance-policy: The home-load-balance-policy element indicates the Java class name to be used to load balance calls made on the home proxy. The class must implement the org.jboss.ha.framework.interface.LoadBalancePolicy interface. The default policy is org.jboss.ha.framework.interfaces.RoundRobin.

• bean-load-balance-policy: The bean-load-balance-policy element indicates the java class name to be used to load balance calls in the bean proxy. The class must implement the org.jboss.ha.framework.interface.LoadBalancePolicy interface. For entity beans and stateful session beans, the default is org.jboss.ha.framework.interfaces.FirstAvailavble. For stateless session beans, org.jboss.ha.framework.interfaces.RoundRobin.

• session-state-manager-jndi-name: The session-state-manager-jndi-name element indicates the name of the org.jboss.ha.framework.interfaces.HASessionState to be used by the container as a backend for state session management in the cluster. Unlike the partition-name element, this is a JNDI name under which the HASessionState implementation is bound. The default location used is /HASessionState/Default.

The ContainerPlugin interface is the parent interface of all container plug-in interfaces. It provides a callback that allows a container to provide each of its plug-ins a pointer to the container the plug-in is working on behalf of. The ContainerPlugin interface is given below.

public interface ContainerPlugin
    extends Service, AllowedOperationsFlags
{
    /** 
     * This callback is set by the container so that the plugin
     * may access its container
     *
     * @param con the container which owns the plugin
     */
    public void setContainer(Container con);
}   

The Interceptor interface enables one to build a chain of method interceptors through which each EJB method invocation must pass. The Interceptor interface is given below.

import org.jboss.invocation.Invocation;
                    
public interface Interceptor 
    extends ContainerPlugin
{
    public void setNext(Interceptor interceptor);
    public Interceptor getNext();
    public Object invokeHome(Invocation mi) throws Exception;
    public Object invoke(Invocation mi) throws Exception;
} 

All interceptors defined in the container configuration are created and added to the container interceptor chain by the EJBDeployer. The last interceptor is not added by the deployer but rather by the container itself because this is the interceptor that interacts with the EJB bean implementation.

The order of the interceptor in the chain is important. The idea behind ordering is that interceptors that are not tied to a particular EnterpriseContext instance are positioned before interceptors that interact with caches and pools.

Implementers of the Interceptor interface form a linked-list like structure through which the Invocation object is passed. The first interceptor in the chain is invoked when an invoker passes a Invocation to the container via the JMX bus. The last interceptor invokes the business method on the bean. There are usually on the order of five interceptors in a chain depending on the bean type and container configuration. Interceptor semantic complexity ranges from simple to complex. An example of a simple interceptor would be LoggingInterceptor, while a complex example is EntitySynchronizationInterceptor.

One of the main advantages of an interceptor pattern is flexibility in the arrangement of interceptors. Another advantage is the clear functional distinction between different interceptors. For example, logic for transaction and security is cleanly separated between the TXInterceptor and SecurityInterceptor respectively.

If any of the interceptors fail, the call is terminated at that point. This is a fail-quickly type of semantic. For example, if a secured EJB is accessed without proper permissions, the call will fail as the SecurityInterceptor before any transactions are started or instances caches are updated.

An InstancePool is used to manage the EJB instances that are not associated with any identity. The pools actually manage subclasses of the org.jboss.ejb.EnterpriseContext objects that aggregate unassociated bean instances and related data.

public interface InstancePool
    extends ContainerPlugin
{
    /** 
     * Get an instance without identity. Can be used
     * by finders and create-methods, or stateless beans
     *
     * @return Context /w instance
     * @exception RemoteException
     */
    public EnterpriseContext get() throws Exception;
    
    /** Return an anonymous instance after invocation.
     *
     * @param ctx
     */
    public void free(EnterpriseContext ctx);
    
    /**
     * Discard an anonymous instance after invocation.
     * This is called if the instance should not be reused,
     * perhaps due to some exception being thrown from it.
     *
     * @param ctx
     */
    public void discard(EnterpriseContext ctx);
    
    /**
     * Return the size of the pool.
     *
     * @return the size of the pool.
     */
    public int getCurrentSize();
    
    /**
     * Get the maximum size of the pool.
     *
     * @return the size of the pool.
     */
    public int getMaxSize();
}

Depending on the configuration, a container may choose to have a certain size of the pool contain recycled instances, or it may choose to instantiate and initialize an instance on demand.

The pool is used by the InstanceCache implementation to acquire free instances for activation, and it is used by interceptors to acquire instances to be used for Home interface methods (create and finder calls).

The container InstanceCache implementation handles all EJB-instances that are in an active state, meaning bean instances that have an identity attached to them. Only entity and stateful session beans are cached, as these are the only bean types that have state between method invocations. The cache key of an entity bean is the bean primary key. The cache key for a stateful session bean is the session id.

public interface InstanceCache 
    extends ContainerPlugin
{
    /**
     * Gets a bean instance from this cache given the identity.
     * This method may involve activation if the instance is not
     * in the cache.
     * Implementation should have O(1) complexity.
     * This method is never called for stateless session beans.
     *
     * @param id the primary key of the bean
     * @return the EnterpriseContext related to the given id
     * @exception RemoteException in case of illegal calls
     * (concurrent / reentrant), NoSuchObjectException if
     * the bean cannot be found.
     * @see #release
     */
    public EnterpriseContext get(Object id)
	throws RemoteException, NoSuchObjectException;
    
    /**
     * Inserts an active bean instance after creation or activation.
     * Implementation should guarantee proper locking and O(1) complexity.
     *
     * @param ctx the EnterpriseContext to insert in the cache
     * @see #remove
     */
    public void insert(EnterpriseContext ctx);
    
    /**
     * Releases the given bean instance from this cache.
     * This method may passivate the bean to get it out of the cache.
     * Implementation should return almost immediately leaving the
     * passivation to be executed by another thread.
     *
     * @param ctx the EnterpriseContext to release
     * @see #get
     */
    public void release(EnterpriseContext ctx);
    
    /**
     * Removes a bean instance from this cache given the identity.
     * Implementation should have O(1) complexity and guarantee
     * proper locking.
     *
     * @param id the pimary key of the bean
     * @see #insert
     */
    public void remove(Object id);
    
    /**
     * Checks whether an instance corresponding to a particular
     * id is active
     *
     * @param id the pimary key of the bean
     * @see #insert
     */
    public boolean isActive(Object id);    
}

In addition to managing the list of active instances, the InstanceCache is also responsible for activating and passivating instances. If an instance with a given identity is requested, and it is not currently active, the InstanceCache must use the InstancePool to acquire a free instance, followed by the persistence manager to activate the instance. Similarly, if the InstanceCache decides to passivate an active instance, it must call the persistence manager to passivate it and release the instance to the InstancePool.

The EntityPersistenceManager is responsible for the persistence of EntityBeans. This includes the following:

public interface EntityPersistenceManager 
    extends ContainerPlugin
{
    /**
     * Returns a new instance of the bean class or a subclass of the
     * bean class.
     *
     * @return the new instance
     */
    Object createBeanClassInstance() throws Exception;
                    
    /**
     * This method is called whenever an entity is to be created. The
     * persistence manager is responsible for calling the ejbCreate method
     * on the instance and to handle the results properly wrt the persistent
     * store.
     *
     * @param m the create method in the home interface that was
     * called
     * @param args any create parameters
     * @param instance the instance being used for this create call
     */
    void createEntity(Method m,
		      Object[] args,
		      EntityEnterpriseContext instance)
	throws Exception;
    
    /**
     * This method is called whenever an entity is to be created. The
     * persistence manager is responsible for calling the ejbPostCreate method
     * on the instance and to handle the results properly wrt the persistent
     * store.
     *
     * @param m the create method in the home interface that was
     * called
     * @param args any create parameters
     * @param instance the instance being used for this create call
     */
    void postCreateEntity(Method m,
			  Object[] args,
			  EntityEnterpriseContext instance)
	throws Exception;
    
    /**
     * This method is called when single entities are to be found. The
     * persistence manager must find out whether the wanted instance is
     * available in the persistence store, and if so it shall use the
     * ContainerInvoker plugin to create an EJBObject to the instance, which
     * is to be returned as result.
     *
     * @param finderMethod the find method in the home interface that was
     * called
     * @param args any finder parameters
     * @param instance the instance to use for the finder call
     * @return an EJBObject representing the found entity
     */
    Object findEntity(Method finderMethod,
		      Object[] args,
		      EntityEnterpriseContext instance)
	throws Exception;
    
    /**
     * This method is called when collections of entities are to be
     * found. The persistence manager must find out whether the wanted
     * instances are available in the persistence store, and if so it
     * shall use the ContainerInvoker plugin to create EJBObjects to
     * the instances, which are to be returned as result.
     *
     * @param finderMethod the find method in the home interface that was
     * called
     * @param args any finder parameters
     * @param instance the instance to use for the finder call
     * @return an EJBObject collection representing the found
     * entities
     */
    Collection findEntities(Method finderMethod,
			    Object[] args,
			    EntityEnterpriseContext instance)
                     throws Exception;
    
    /**
     * This method is called when an entity shall be activated. The
     * persistence manager must call the ejbActivate method on the
     * instance.
     *
     * @param instance the instance to use for the activation
     *
     * @throws RemoteException thrown if some system exception occurs
     */
    void activateEntity(EntityEnterpriseContext instance)
	throws RemoteException;
                    
    /**
     * This method is called whenever an entity shall be load from the
     * underlying storage. The persistence manager must load the state
     * from the underlying storage and then call ejbLoad on the
     * supplied instance.
     *
     * @param instance the instance to synchronize
     *
     * @throws RemoteException thrown if some system exception occurs
     */
    void loadEntity(EntityEnterpriseContext instance)
	throws RemoteException;
    
    /**
     * This method is used to determine if an entity should be stored.
     *
     * @param instance the instance to check
     * @return true, if the entity has been modified
     * @throws Exception thrown if some system exception occurs
     */
    boolean isModified(EntityEnterpriseContext instance) throws Exception;
    
    /**
     * This method is called whenever an entity shall be stored to the
     * underlying storage. The persistence manager must call ejbStore
     * on the supplied instance and then store the state to the
     * underlying storage.
     *
     * @param instance the instance to synchronize
     *
     * @throws RemoteException thrown if some system exception occurs
     */
    void storeEntity(EntityEnterpriseContext instance)
	throws RemoteException;
    
    /**
     * This method is called when an entity shall be passivate. The
     * persistence manager must call the ejbPassivate method on the
     * instance.
     *
     * @param instance the instance to passivate
     *
     * @throws RemoteException thrown if some system exception occurs
     */
    void passivateEntity(EntityEnterpriseContext instance)
	throws RemoteException;
    
    /**
     * This method is called when an entity shall be removed from the
     * underlying storage. The persistence manager must call ejbRemove
     * on the instance and then remove its state from the underlying
     * storage.
     *
     * @param instance the instance to remove
     *
     * @throws RemoteException thrown if some system exception occurs
     * @throws RemoveException thrown if the instance could not be removed
     */
    void removeEntity(EntityEnterpriseContext instance)
	throws RemoteException, RemoveException;
}

As per the EJB 2.1 specification, JBoss supports two entity bean persistence semantics: container managed persistence (CMP) and bean managed persistence (BMP). The CMP implementation uses an implementation of the org.jboss.ejb.EntityPersistanceStore interface. By default this is the org.jboss.ejb.plugins.cmp.jdbc.JDBCStoreManager which is the entry point for the CMP2 persistence engine. The EntityPersistanceStore interface is shown below.

public interface EntityPersistenceStore 
    extends ContainerPlugin
{
    /**
     * Returns a new instance of the bean class or a subclass of the
     * bean class.
     *
     * @return the new instance
     *
     * @throws Exception
     */
    Object createBeanClassInstance() 
        throws Exception;
    
    /**
     * Initializes the instance context.
     *
     * <p>This method is called before createEntity, and should
     * reset the value of all cmpFields to 0 or null.
     *
     * @param ctx
     *
     * @throws RemoteException
     */
    void initEntity(EntityEnterpriseContext ctx);
    
    /**
     * This method is called whenever an entity is to be created.  The
     * persistence manager is responsible for handling the results
     * properly wrt the persistent store.
     *
     * @param m the create method in the home interface that was
     * called
     * @param args any create parameters
     * @param instance the instance being used for this create call
     * @return The primary key computed by CMP PM or null for BMP
     *
     * @throws Exception
     */
    Object createEntity(Method m,
			Object[] args,
			EntityEnterpriseContext instance)
        throws Exception;
    
    /**
     * This method is called when single entities are to be found. The
     * persistence manager must find out whether the wanted instance
     * is available in the persistence store, if so it returns the
     * primary key of the object.
     *
     * @param finderMethod the find method in the home interface that was
     * called
     * @param args any finder parameters
     * @param instance the instance to use for the finder call
     * @return a primary key representing the found entity
     *
     * @throws RemoteException thrown if some system exception occurs
     * @throws FinderException thrown if some heuristic problem occurs
     */
    Object findEntity(Method finderMethod,
		      Object[] args,
		      EntityEnterpriseContext instance)
        throws Exception;
    
    /**
     * This method is called when collections of entities are to be
     * found. The persistence manager must find out whether the wanted
     * instances are available in the persistence store, and if so it
     * must return a collection of primaryKeys.
     *
     * @param finderMethod the find method in the home interface that was
     * called
     * @param args any finder parameters
     * @param instance the instance to use for the finder call
     * @return an primary key collection representing the found
     * entities
     *
     * @throws RemoteException thrown if some system exception occurs
     * @throws FinderException thrown if some heuristic problem occurs
     */
    Collection findEntities(Method finderMethod,
			    Object[] args,
			    EntityEnterpriseContext instance)
        throws Exception;
    
    /**
     * This method is called when an entity shall be activated.
     *
     * <p>With the PersistenceManager factorization most EJB
     * calls should not exists However this calls permits us to
     * introduce optimizations in the persistence store. Particularly
     * the context has a "PersistenceContext" that a PersistenceStore
     * can use (JAWS does for smart updates) and this is as good a
     * callback as any other to set it up.
     * @param instance the instance to use for the activation
     *
     * @throws RemoteException thrown if some system exception occurs
     */
    void activateEntity(EntityEnterpriseContext instance)
        throws RemoteException;
    
    /**
     * This method is called whenever an entity shall be load from the
     * underlying storage. The persistence manager must load the state
     * from the underlying storage and then call ejbLoad on the
     * supplied instance.
     *
     * @param instance the instance to synchronize
     *
     * @throws RemoteException thrown if some system exception occurs
     */
    void loadEntity(EntityEnterpriseContext instance)
        throws RemoteException;
    
    /**
     * This method is used to determine if an entity should be stored.
     *
     * @param instance the instance to check
     * @return true, if the entity has been modified
     * @throws Exception thrown if some system exception occurs
     */
    boolean isModified(EntityEnterpriseContext instance)
        throws Exception;
    
    /**
     * This method is called whenever an entity shall be stored to the
     * underlying storage. The persistence manager must call ejbStore
     * on the supplied instance and then store the state to the
     * underlying storage.
     *
     * @param instance the instance to synchronize
     *
     * @throws RemoteException thrown if some system exception occurs
     */
    void storeEntity(EntityEnterpriseContext instance)
        throws RemoteException;
    
    /**
     * This method is called when an entity shall be passivate. The
     * persistence manager must call the ejbPassivate method on the
     * instance.
     *
     * <p>See the activate discussion for the reason for
     * exposing EJB callback * calls to the store.
     *
     * @param instance the instance to passivate
     *
     * @throws RemoteException thrown if some system exception occurs
     */
    void passivateEntity(EntityEnterpriseContext instance)
        throws RemoteException;
    
    /**
     * This method is called when an entity shall be removed from the
     * underlying storage. The persistence manager must call ejbRemove
     * on the instance and then remove its state from the underlying
     * storage.
     *
     * @param instance the instance to remove
     *
     * @throws RemoteException thrown if some system exception occurs
     * @throws RemoveException thrown if the instance could not be removed
     */
    void removeEntity(EntityEnterpriseContext instance)
        throws RemoteException, RemoveException;
}

The default BMP implementation of the EntityPersistenceManager interface is org.jboss.ejb.plugins.BMPPersistenceManager. The BMP persistence manager is fairly simple since all persistence logic is in the entity bean itself. The only duty of the persistence manager is to perform container callbacks.

The StatefulSessionPersistenceManager is responsible for the persistence of stateful SessionBeans. This includes the following:

The StatefulSessionPersistenceManager interface is shown below.

public interface StatefulSessionPersistenceManager 
    extends ContainerPlugin
{
    public void createSession(Method m, Object[] args,
			      StatefulSessionEnterpriseContext ctx)
	throws Exception;
    
    public void activateSession(StatefulSessionEnterpriseContext ctx)
	throws RemoteException;
    
    public void passivateSession(StatefulSessionEnterpriseContext ctx)
	throws RemoteException;
    
    public void removeSession(StatefulSessionEnterpriseContext ctx)
	throws RemoteException, RemoveException;
    
    public void removePassivated(Object key);
}

The default implementation of the StatefulSessionPersistenceManager interface is org.jboss.ejb.plugins.StatefulSessionFilePersistenceManager. As its name implies, StatefulSessionFilePersistenceManager utilizes the file system to persist stateful session beans. More specifically, the persistence manager serializes beans in a flat file whose name is composed of the bean name and session id with a .ser extension. The persistence manager restores a bean's state during activation and respectively stores its state during passivation from the bean's .ser file.

Fortunately, JBoss is able to perform deadlock detection. JBoss holds a global internal graph of waiting transactions and what transactions they are blocking on. Whenever a thread determines that it cannot acquire an entity bean lock, it figures out what transaction currently holds the lock on the bean and add itself to the blocked transaction graph. An example of what the graph may look like is given in Table 5.1, “An example blocked transaction table”.

Before the thread actually blocks it tries to detect whether there is deadlock problem. It does this by traversing the block transaction graph. As it traverses the graph, it keeps track of what transactions are blocked. If it sees a blocked node more than once in the graph, then it knows there is deadlock and will throw an ApplicationDeadlockException. This exception will cause a transaction rollback which will cause all locks that transaction holds to be released.

Since JBoss can detect application deadlock, you should write your application so that it can retry a transaction if the invocation fails because of the ApplicationDeadlockException. Unfortunately, this exception can be deeply embedded within a RemoteException, so you have to search for it in your catch block. For example:

try {
    // ...
} catch (RemoteException ex) {
    Throwable cause = null;
    RemoteException rex = ex;
    while (rex.detail != null) {
        cause = rex.detail;
        if (cause instanceof ApplicationDeadlockException) {
	        // ... We have deadlock, force a retry of the transaction.
            break;
        }
        if (cause instanceof RemoteException) {
            rex = (RemoteException)cause;
        }
    }
}

The EntityLockMonitor MBean service allows one to view basic locking statistics as well as printing out the state of the transaction locking table. To enable this monitor uncomment its configuration in the conf/jboss-service.xml:

<mbean code="org.jboss.monitor.EntityLockMonitor"
       name="jboss.monitor:name=EntityLockMonitor"/>

The EntityLockMonitor has no configurable attributes. It does have the following read-only attributes:

It also has the following operations:

Make your transactions as short-lived and fine-grained as possible. The shorter the transaction you have, the less likelihood you will have concurrent access collisions and your application throughput will go up.

Ordering the access to your entity beans can help lessen the likelihood of deadlock. This means making sure that the entity beans in your system are always accessed in the same exact order. In most cases, user applications are just too complicated to use this approach and more advanced configurations are needed.

Entity beans can be marked as read-only. When a bean is marked as read-only, it never takes part in a transaction. This means that it is never transactionally locked. Using commit-option D with this option is sometimes very useful when your read-only bean's data is sometimes updated by an external source.

To mark a bean as read-only, use the read-only flag in the jboss.xml deployment descriptor.

<jboss>
    <enterprise-beans>
        <entity>
            <ejb-name>MyEntityBean</ejb-name>
            <jndi-name>MyEntityHomeRemote</jndi-name>
            <read-only>True</read-only>
        </entity>
    </enterprise-beans>
</jboss>

After reading and understanding the default locking behavior of entity beans, you're probably wondering, "Why lock the bean if its not modifying the data?" JBoss allows you to define what methods on your entity bean are read only so that it will not lock the bean within the transaction if only these types of methods are called. You can define these read only methods within a jboss.xml deployment descriptor. Wildcards are allowed for method names. The following is an example of declaring all getter methods and the anotherReadOnlyMethod as read-only.

<jboss>
    <enterprise-beans>
        <entity>
            <ejb-name>nextgen.EnterpriseEntity</ejb-name>
            <jndi-name>nextgen.EnterpriseEntity</jndi-name>
            <method-attributes>
                <method>
                    <method-name>get*</method-name>
                    <read-only>true</read-only>
                </method>
                <method>
                    <method-name>anotherReadOnlyMethod</method-name>
                    <read-only>true</read-only>
                </method>
            </method-attributes>
        </entity>
    </enterprise-beans>
</jboss> 

The Instance Per Transaction policy is an advanced configuration that can totally wipe away deadlock and throughput problems caused by JBoss's default locking policy. The default Entity Bean locking policy is to only allow one active instance of a bean. The Instance Per Transaction policy breaks this requirement by allocating a new instance of a bean per transaction and dropping this instance at the end of the transaction. Because each transaction has its own copy of the bean, there is no need for transaction based locking.

This option does sound great but does have some drawbacks right now. First, the transactional isolation behavior of this option is equivalent to READ_COMMITTED. This can create repeatable reads when they are not desired. In other words, a transaction could have a copy of a stale bean. Second, this configuration option currently requires commit-option B or C which can be a performance drain since an ejbLoad must happen at the beginning of the transaction. But, if your application currently requires commit-option B or C anyways, then this is the way to go. The JBoss developers are currently exploring ways to allow commit-option A as well (which would allow the use of caching for this option).

JBoss has container configurations named Instance Per Transaction CMP 2.x EntityBean and Instance Per Transaction BMP EntityBean defined in the standardjboss.xml that implement this locking policy. To use this configuration, you just have to reference the name of the container configuration to use with your bean in the jboss.xml deployment descriptor as show below.

<jboss>
    <enterprise-beans>
        <entity>
            <ejb-name>MyCMP2Bean</ejb-name>
            <jndi-name>MyCMP2</jndi-name>
            <configuration-name>
                Instance Per Transaction CMP 2.x EntityBean
            </configuration-name>
        </entity>
        <entity>
            <ejb-name>MyBMPBean</ejb-name>
            <jndi-name>MyBMP</jndi-name>
            <configuration-name>
                Instance Per Transaction BMP EntityBean
            </configuration-name>
        </entity>
    </enterprise-beans>
</jboss>

Many JBoss users observe that locking does not seem to be working and see concurrent access to their beans, and thus dirty reads. Here are some common reasons for this:

An IllegalStateException with the message "removing bean lock and it has tx set!" usually means that you have not implemented equals and/or hashCode correctly for your custom/complex primary key class, or that your primary key class is not implemented correctly for serialization.

One long outstanding bug of JBoss is that on a transaction timeout, that transaction is only marked for a rollback and not actually rolled back. This responsibility is delegated to the invocation thread. This can cause major problems if the invocation thread hangs indefinitely since things like entity bean locks will never be released. The solution to this problem is not a good one. You really just need to avoid doing stuff within a transaction that could hang indefinitely. One common mistake is making connections across the internet or running a web-crawler within a transaction.